Repair and operation of the Toyota Camry car - 11.11. Decorative panels of bumpers//Toyota Camry of 1996-2001 /

Toyota Camry

1996-2001 of release

Repair and operation of the car



Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
- 11. Body
   11.2. Vinyl finishing
   11.3. Upholstery and rugs
   11.4. Insignificant damages of a body
   11.5. Considerable damages of a body
   11.6. Loops and locks
   11.7. Windshield and motionless glasses
   11.8. Central lock
   11.9. Cowl
   11:10. Lock of a cowl and cable of the drive of the lock
   11:11. Decorative panels of bumpers
   11:12. Forward wing
   11:13. Trunk lid
   11:14. Latch and lock of a trunk lid
   11:15. Cable of the drive of unlocking of a door of a fuel tank / trunk lid
   11:16. Facing panels of doors
   11:17. Door
   11:18. Latch, lock of a door and handle
   11:19. Door glass
   11:20. Window regulator
   11:21. Mirrors
   11:22. Central floor section
   11:23. Decorative panels of a forward part of facing of salon
   11:24. Casings of a steering column
   11:25. Dashboard
   11:26. Facing of a frame of a windshield
   11:27. Seats
   11:28. Ware tray
+ 12. Electric equipment



11:11. Decorative panels of bumpers

FRONT BUMPER

PERFORMANCE ORDER
1. Lift the car and establish on supports.
2. Disconnect negative and then the positive plug from the battery and wait not less than 2 minutes.

3. On the Camry models turn off a bolt of fastening of the panel of a bumper and remove plastic percussion caps of fastening of the panel of a bumper.

Prevention

Hook buttons of the central percussion caps the small screw-driver, not to delete buttons as they are pressed in steel futorka.


4. On the Avalon models unscrew two screws and remove percussion caps of fastening of a lattice (arrow).
5. Then disconnect sockets of fog lamps (if are provided) and turn off bolts (shooters) of fastening of the panel of a front bumper.
6. Remove two lower percussion caps.
7. Then unscrew screws (shooters) of fastening of antisplash panels to the lower part of a bumper then access to a bolt of fastening of the panel of a bumper to the lower part of a wing (Avalon model) is provided.
8. Installation is carried out upside-down. At installation previously be convinced that latches from the back of a bumper came into the corresponding brackets on a body. It is expedient to establish a bumper together.

REAR BUMPER

Details of fastening of a rear bumper (Avalon model)


PERFORMANCE ORDER
1. Remove plastic percussion caps (shooters) and unscrew screws of fastening of the lower edge of the panel of a bumper (Camry model).
2. Turn off nuts of fastening of a bumper on corners in a luggage carrier. For access to nuts remove facing.
3. Open a trunk lid and remove percussion caps (shooters) or brackets fixing the top edge of the panel of a bumper. Remove the bumper panel.

Prevention

Hook buttons of the central percussion caps the small screw-driver, not to delete buttons as they are pressed in steel futorka. For removal of bolts from body openings when jamming it is possible to beat out a bolt easy blows of the plastic hammer.


4. Installation is carried out upside-down.