Toyota Camry

1996-2001 of release

Repair and operation of the car

Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
- 2. Maintenance
   2.2. Schedule of servicing of Toyota Camry/Avalon
   2.3. Primary and secondary checks
   2.4. Check of level of oil and liquids
   2.5. Check of a condition of tires and pressure in tires
   2.6. Check of level of liquid of system of hydrostrengthening of steering
   2.7. Check of level of automatic transmission liquid
   2.8. Replacement of engine oil and oil filter
   2.9. Survey and replacement of brushes of screen wipers
   2.10. Check, servicing and accumulator charging
   2.11. Check, adjustment of a tension and replacement of a driving belt
   2.12. Check and replacement of hoses in a motive compartment
   2.13. Check of the cooling system
   + 2.14. Shift of wheels
   2.15. Check of the brake system
   2.16. Replacement of the air filter
   2.17. Check of a power supply system
   2.18. Check of level of liquid of differential (automatic transmission)
   2.19. Check of level of MKPP oil
   2.20. Check of steering and suspension bracket
   2.21. Check of covers of half shafts
   2.22. Check of final system
   2.23. Height and free wheeling of pedals of coupling and brake
   2.24. Replacement of the fuel filter
   2.25. Replacement of cooling liquid and washing of the cooling system
   2.26. Check of the system controlling releases of vapors of fuel
   2.27. Automatic transmission liquid replacement
   2.28. MKPP oil replacement
   2.29. Check of fastenings of a body
   2.30. Check and replacement of spark plugs
   2.31. Check and replacement of wires of spark plugs
   2.32. Check and adjustment of gaps of valves
   2.33. Replacement of laying of a cover of a jellied mouth of the fuel tank
   2.34. Check and replacement of the valve of ventilation of a case
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

2.32. Check and adjustment of gaps of valves

GENERAL INFORMATION

Gaps of final valves of the first and third cylinders and gaps of inlet valves of the first and second cylinders (four-cylinder engine)

Gaps of valves (six-cylinder engine)

1. Right head, final valves

2. Right head, inlet valves

3. Left head, inlet valves

4. Left head, final valves

Gaps of valves of the 4-cylinder engine (remained)

IN – Inlet valves

EX – Final valves

Gaps of valves of the 6-cylinder engine (remained)

IN – Inlet valves

EX – Final valves

The gaps of valves of the 6-cylinder engine which (remained) – 2

IN – Inlet valves

EX – Final valves

PERFORMANCE ORDER

1. Disconnect a wire of the minus plug of the accumulator.
2. In four-cylinder models disconnect wires of spark plugs.
3. In six-cylinder engines merge cooling liquid and remove the air filter. Disconnect wires of spark plugs of a back row of cylinders and remove wires and coils of ignition of candles of a forward row.
4. Unscrew spark plugs.
5. Uncover a head.
6. Install the N1 cylinder piston in the provision of VMT at the time of a compression step.
	7. Measure a gap of each of valves by means of a set of probes.
8. On models with the four-cylinder engine turn a bent shaft on one whole revolution and combine adjusting marks in a pulley of a bent shaft. Measure gaps of the remained valves (see rice. Gaps of valves of the 4-cylinder engine (remained)).
9. On models with the six-cylinder engine turn a bent shaft on 2/3 turns (240 degrees) clockwise. Measure gaps of the specified valves (see rice. Gaps of valves of the 6-cylinder engine (remained)). Turn a bent shaft on 2/3 turns and measure gaps of the remained valves (see rice. The gaps of valves of the 6-cylinder engine which (remained) – 2).
10. Turn a bent shaft so that the cam over the valve demanding adjustment was lifted up.
	11. Turn the valve elevator a cut to a spark plug. Install the tool and you press the elevator. Squeeze the elevator the special tool to remove laying.

12. Remove laying by means of the small screw-driver or a magnet.
	13. Measure laying thickness by means of a micrometer.
14. Calculate the required thickness of new laying by the following formula: N = T + (A – V) T = thickness of an old washer A = valvate gap N = thickness of a new washer V = the recommended valvate gap.
15. Establish new laying, and repeatedly check a valvate gap.