Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
- 3. Engines
+ 3.1.2. Check of a compression
- 3.2. 6-cylinder two-row V6 3,0 engines of l
3.2.2. Check of a compression
3.2.3. Top Dead Point (TDP) of the N1 piston
3.2.4. Covers of heads of cylinders
3.2.5. Inlet collector
3.2.6. Final collectors
3.2.7. Gas-distributing belt and asterisks
3.2.8. Forward epiploon of a bent shaft
3.2.9. Epiploons of camshafts
3.2.10. Camshafts and elevators of valves
3.2.11. Heads of cylinders
3.2.12. Oil pallet
3.2.13. Oil pump
3.2.14. Flywheel / drive plate
3.2.15. Back epiploon of a bent shaft
3.2.16. Fastenings of the engine
+ 3.3. Partition of engines
+ 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment
3.2. 6-cylinder two-row V6 3,0 engines of l
3.2.1. Technical characteristics
| GENERAL INFORMATION |
Type of a motive compartment of models with the 6-cylinder engine
|
1. Tank of brake fluid
2. Casing of the air filter 3. Accumulator 4. The probe for measurement of level of liquid of the automatic transmission 5. Cover of a maslozalivny mouth of the engine 6. Oil filter |
7. The probe for measurement of level of oil of the engine 8. Radiator hose 9. Tank of liquid of steklomyvatel 10. Broad tank of the cooling system of the engine 11. Tank of liquid of system of hydrostrengthening |
| Marking of the engine |
1MZ-FE
|
| Numbering of cylinders (from a gas-distributing belt to the transmission) | |
| Right row |
1 – 3 – 5
|
| Left row |
2 – 4 – 6
|
| Sequence of operation of cylinders |
1 – 2 – 3 – 4 – 5 – 6
|
| Volume |
3,0 liters
|
| Head of cylinders | |
| Admissible deformation of surfaces: | |
| – heads |
0,099
|
| – inlet collector |
0,079
|
| – final collector |
0,498
|
| Camshaft | |
| Valve gap (engine cold): | |
| – inlet |
0,127 – 0,229
|
| – final |
0,280 – 0,381
|
| Diameter of a neck of the bearing: | |
| – shaft of inlet valves |
26,950 – 26,965
|
| – shaft of final valves |
26,957 – 26,974
|
| Lubricant gap of bearings | |
| Standard: | |
| – shaft of inlet valves |
0,035 – 0,071
|
| – shaft of final valves |
0,026 – 0,061
|
| Limit: | |
| – shaft of inlet valves |
0,099
|
| – shaft of final valves |
0,089
|
| Cam height | |
| Shaft of inlet valves: | |
| – standard |
42,111 – 42,210
|
| – limit |
41,961
|
| Shaft of final valves: | |
| – standard |
41,961 – 42,060
|
| – limit |
41,811
|
| Axial gap: | |
| – standard |
0,041 – 0,089
|
| – limit |
0,119
|
| – the most admissible beating |
0,061
|
| District gap of camshafts: | |
| – standard |
0,020 – 0,201
|
| – limit |
0,478
|
| Trailer gap of a spring of a gear wheel of the camshaft |
18,085 – 18,796
|
| Ledge of a natyazhitel of a gas-distributing belt |
10,008 – 10,795
|
| Elevators: | |
| – external diameter |
30,965 – 30,975
|
| – diameter of a nest |
31,001 – 31,016
|
| Lubricant gap: | |
| – standard |
0,023 – 0,051
|
| – limit |
0,071
|
| Oil pump | |
| Gap between the conducted gear wheel and a casing: | |
| – standard |
0,099 – 0,175
|
| – limit |
0,300
|
| Gap between teeth of gear wheels: | |
| – standard |
0,109 – 0,239
|
| – limit |
0,351
|
| Gap between the planes of gear wheels and the plane of the pump: | |
| – standard |
0,031 – 0,089
|
| – limit |
0,150
|
Moments of an inhaling of threaded connections, N. of m.
| Air conditioning system compressor arm bolts |
26
|
| Bolts of the lower part of an inlet collector |
15
|
| Bolts of the top camera of an inlet collector |
43
|
| Bolts of an arm of the top camera of a collector |
19
|
| Bolts of a final collector |
49
|
| Bolt of a pulley of a bent shaft |
216
|
| Bolts of a cover of a gas-distributing belt |
8
|
| Bolts of intermediate pulleys | |
| – N1 pulley |
34
|
| – N2 pulley |
43
|
| Bolts of a natyazhitel of a gas-distributing belt |
27
|
| Camshaft pulley bolts |
128
|
| Bolts of covers of bearings of the camshaft |
16
|
| Bolts of a head of cylinders | |
| – step 1 |
54
|
| – step 2 |
Tighten by 90 degrees
|
| Bolts of a head of cylinders (drowned) |
18
|
| Bolts of the oil pallet | |
| Aluminum section |
19
|
| Steel section |
8
|
| Bolts of the oil pump | |
| Bolts with a head of 10 mm |
8
|
| Bolts with a head of 12 mm, |
10
|
| Bolts with a head of 14 mm |
35
|
| Assembly bolts of a maslozaborny branch pipe |
8
|
| Flywheel bolts / drive plate |
83
|
| Bolts of a casing of a back epiploon of a bent shaft |
8
|
| Nuts of a cover of a head of cylinders |
8
|
| Fastenings of the engine | |
| Bolts of adjusting draft of shift of the engine |
64
|
| The bolts fixing a forward support to a body | |
| Green |
65
|
| Silver |
43
|
| Only Camry models, all bolts |
80
|
| Bolts of the shock-absorber of a forward support |
48
|
| Nuts of a back support |
65
|
