Toyota Camry

1996-2001 of release

Repair and operation of the car

Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
- 3. Engines
   + 3.1.2. Check of a compression
   + 3.2. 6-cylinder two-row V6 3,0 engines of l
   - 3.3. Partition of engines
      3.3.1.2. 6-cylinder two-row engines
      3.3.2. Capital repairs of the engine – general comments
      3.3.3. Diagnostics of the engine by means of the vacuum gage
      3.3.4. Capital repairs of the engine – an alternative
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and installation of the engine
      3.3.7. Engine partition
      3.3.8. Head of cylinders and valves
      3.3.9. Balancing device (4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. Bent shaft
      3.3.12. Block of cylinders
      3.3.13. Honingovaniye of cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a bent shaft
      3.3.18. Back epiploon of a bent shaft
      3.3.19. Conrod bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is rather live, than is dead …
      3.3.22. Analysis of smoke of an exhaust
      3.3.23. A gear belt for the gas distribution mechanism drive
      3.3.24. Emergence in deposit oil
      3.3.25. Engine overheat
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.3.6. Removal and installation of the engine

Removal

PERFORMANCE ORDER

1. Pit pressure in fuel system.
2. Disconnect a wire of the minus plug of the accumulator.
3. Remove the accumulator and an arm of the accumulator.
4. Remove an engine cowl.
5. Remove the air filter.
6. Lift and fix the car. Merge cooling liquid and engine oil. Take off driving belts.
	7. Mark both ends and disconnect vacuum hoses, hoses of cooling liquid and final gases. Disconnect wires and fuel tubes. To mark wires use an insulating tape.
8. Remove a broad tank of the cooling system and a tank of windscreen washers.
9. Remove radiator fans, a casing of fans and a radiator.
10. Disconnect heater hoses.
11. Disconnect the fuel tubes connecting the engine to a body.
12. Disconnect a rope of a butterfly valve, a rope of the throttle valve of the transmission and a rope of the sensor of a speedometer from the engine.
13. Disconnect holders of a plait of wires of the engine.
14. Unscrew assembly bolts of the pump of system of strengthening of a wheel. Whenever possible shift the pump aside without disconnecting from it hoses. If necessary remove the pump.
	15. Remove the compressor of the air conditioner and shift it aside. Do not disconnect hoses from the compressor.
16. Disconnect an exhaust pipe(s) from a collector(s).
	17. In four-cylinder engines remove an oil filter, disconnect hoses from the oil heater and remove the oil heater (shooter).
18. Fix a chain on the hooks intended for a raising of the engine and connect a chain to the elevator.
	19. Remove the leading axis (A) from passenger sitting, unscrew a through bolt of a support of the engine (V) and remove a back arm of the engine (C).
	20. Unscrew the bolt fixing a forward support of the engine to a body(bodies) if you remove the engine together with the transmission, remove the shock-absorber of the engine (B).
21. In models with the automatic transmission remove the dustproof screen of the hydrotransformer, remove clamps of the hydrotransformer and slightly press the hydrotransformer into a transmission casing.
22. If you remove only the engine, unscrew bolts and disconnect the transmission.
23. Check that nothing prevented removal of the engine.
24. Establish a jack under the transmission. Unscrew bolts from engine support.
	25. Slowly lift the engine on the elevator (in the drawing the 4-cylinder engine together with the transmission is shown).
26. Lower the engine on specially equipped rack or on a workshop floor.

Installation

PERFORMANCE ORDER

1. In engines with the mechanical transmission, examine elements of coupling and grease press the bearing.

2. In engines with the automatic transmission, examine laying and the plug of the hydrotransformer and grease its forward part.

3. Install the engine upside-down of removal.