Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
- 3. Engines
+ 3.1.2. Check of a compression
+ 3.2. 6-cylinder two-row V6 3,0 engines of l
- 3.3. Partition of engines
3.3.1.2. 6-cylinder two-row engines
3.3.2. Capital repairs of the engine – general comments
3.3.3. Diagnostics of the engine by means of the vacuum gage
3.3.4. Capital repairs of the engine – an alternative
3.3.5. Auxiliary elements of the engine
3.3.6. Removal and installation of the engine
3.3.7. Engine partition
3.3.8. Head of cylinders and valves
3.3.9. Balancing device (4-cylinder engine)
3.3.10. Pistons and rods
3.3.11. Bent shaft
3.3.12. Block of cylinders
3.3.13. Honingovaniye of cylinders
3.3.14. Radical bearings and bearings of rods
3.3.15. Measurement of size of a free wheeling of the balancing device
3.3.16. Piston rings
3.3.17. Radical bearings of a bent shaft
3.3.18. Back epiploon of a bent shaft
3.3.19. Conrod bearings
3.3.20. Installation of the balancing device of the engine
3.3.21. It is rather live, than is dead …
3.3.22. Analysis of smoke of an exhaust
3.3.23. A gear belt for the gas distribution mechanism drive
3.3.24. Emergence in deposit oil
3.3.25. Engine overheat
+ 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment
3.3.7. Engine partition
| GENERAL INFORMATION |
The 4-cylinder engine – elements of the block of cylinders
|
1. Piston ring (compression)
2. Piston ring (oil scraper) 3. Piston finger 4. Rod plug 5. Block of cylinders 6. Back plate 7. Laying 8. Back epiploon of a bent shaft 9. Casing of a back epiploon 10. Flywheel or drive plate 11. Drive plate 12. Back intermediate ring 13. Forward intermediate ring 14. Balancing device engine 15. Laying 16. Maslozaborny branch pipe 17. Laying |
18. Dividing partition of the oil pallet 19. Cover of the radical bearing 20. Insert of the radical bearing 21. Persistent half ring 22. Bent shaft 23. Laying 24. Oil pump 25. Forward epiploon of a bent shaft 26. Right arm of the engine 27. Arm of the pump of the hydraulic booster 28. Rod cover 29. Insert of the conrod bearing 30. Rod 31. Lock ring 32. Piston 33. Spring of an oil scraper ring 34. Piston ring (compression) |
The 6-cylinder two-row engine – elements of the block of cylinders
|
1. Piston ring (compression)
2. Piston ring (compression) 3. Piston ring (oil scraper) 4. Piston 5. Rod plug 6. Rod 7. Insert of the conrod bearing 8. Rod cover 9. Back plate 10. Flywheel 11. Back epiploon of a bent shaft 12. Casing of a back epiploon 13. Arm of an oil filter 14. Back intermediate ring 15. Drive plate 16. Forward intermediate ring 17. Insert of the radical bearing 18. Cover of the radical bearing |
19. Sealing washer 20. Sealing half ring 21. Bent shaft 22. Maslozaborny branch pipe 23. Laying 24. Oil pressure sensor 25. Oil pump 26. Epiploon 27. Sealing ring 28. Sensor of detonation combustion 29. Clamp 30. Drain hose 31. Drain crane 32. Lock ring 33. Porshnevy finger 34. Spring of an oil scraper ring 35. Tube of cooling liquid 36. Arm of an intermediate pulley |
You carry out an engine partition in the pure place which is specially equipped for this purpose.
Fix the engine at the special stand, or on a floor.
Prepare all necessary tools and observe precautionary measures during this difficult procedure.
