Toyota Camry

1996-2001 of release

Repair and operation of the car

Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
- 7. Exhaust system
   - 7.2. Systems of decrease in toxicity of exhaust gases
      7.2.2. Technical characteristics
      7.2.3. OBD II system
      7.2.4. OBD computer of II system (Powertrain Control Module)
      7.2.5. Sensor of turn of a butterfly valve
      7.2.6. The sensor of absolute pressure in the soaking-up collector
      7.2.7. Sensor of a mass consumption of air
      7.2.8. The sensor of temperature of the soaked-up air (IAT sensor)
      7.2.9. Sensor of temperature of cooling liquid (ECT sensor)
      7.2.10. Sensor of rotation of the crankshaft
      7.2.11. Sensor of rotation of a cam-shaft
      7.2.12. Contact sensor of pressure of the hydraulic booster
      7.2.13. The sensor of content of oxygen in the fulfilled gases
      7.2.14. Detonation sensor
      7.2.15. Car speed sensor
      7.2.16. Perepuskna air valve of idling (IAC valve)
      7.2.17. System of the choice of the channel of absorption (ACIS system)
      7.2.18. System of ventilation of a case
      7.2.19. System of recirculation
      7.2.20. System of catching of vapors of gasoline
      7.2.21. Converter
      7.2.22. Rub in one – or how to save the catalyst
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

7.2.10. Sensor of rotation of the crankshaft

GENERAL INFORMATION

On 4-cylinder engines the sensor is mounted under a cover of a gear belt, on V6 engines – over a crankshaft pulley.

The place of installation of the sensor of rotation of the crankshaft on 4-cylinder engines

1. Wire
2. Socket
3. Generator
4. Crankshaft pulley guide
5. Sensor of rotation of the crankshaft
6, 7, 9, 14. Collar

8. Sensor socket
10. Pulley
11. Belt N1 cover
12. Belt N2 cover
13, 15. Laying

The place of installation of the sensor of rotation of the crankshaft on 6-cylinder engines

1. Socket

2. Sensor

Check

4-CYLINDER ENGINES

PERFORMANCE ORDER

	1. Disconnect the socket of conducting of the sensor about the generator and check sensor resistance (the arrow specified a sensor arrangement).
2. Together with the sensor it is necessary to check also the module of the computer for what the module should be removed and handed over in car service.

6-CYLINDER ENGINES

PERFORMANCE ORDER

	1. Because of the complicated access to the socket the sensor is recommended to be removed (the arrow specified a sensor arrangement). Check resistance on the removed sensor.
2. Having warmed up the engine, or having removed the sensor and having placed in boiled water, check sensor resistance at 80 °C which has to be 250–300 Ohms.

Replacement

PERFORMANCE ORDER

1. Disconnect the battery from weight.

2. On 4-cylinder engines uncover a belt (see rice. The place of installation of the sensor of rotation of the crankshaft on 4-cylinder engines).

3. On 6-cylinder engines for access to the sensor remove the protective panel of a wheel niche (see rice. The place of installation of the sensor of rotation of the crankshaft on 6-cylinder engines). Disconnect the socket, turn off a bolt and remove the sensor.