Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
- 9. Running gear
- 9.1.2. Technical characteristics
9.1.3. Stabilizer of cross stability of a forward suspension bracket
9.1.4. Rack of a forward suspension bracket
9.1.5. Rack and spring of a suspension bracket
9.1.6. Suspension bracket lever
9.1.7. Spherical support
9.1.8. Rotary fist and nave
9.1.9. Nave and bearing of a forward wheel
9.1.10. Stabilizer and plugs of the stabilizer of a back suspension bracket
9.1.11. Rack of a back suspension bracket
9.1.12. Longitudinal bar
9.1.13. Levers of a back suspension bracket
9.1.14. Nave and bearing of a back wheel
9.1.15. Arm of a back suspension bracket
9.1.16. Angles of installation of wheels
+ 9.2. Steering
+ 9.3. Half shafts
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment
|
Replacement
| PERFORMANCE ORDER |
1. Lift the car and remove a wheel.
Prevention
If the spherical support is removed a stripper of gripping type, then before dismantle of a wheel release a nut of a nave of a wheel (half shaft).
|
|
REMOVAL OF THE SUPPORT BY MEANS OF THE SLIDING BIFURCATE STRIPPER
Prevention
The procedure considered below provides the most bystry removal of a spherical support, however, at the same time the support finger cover for certain will be damaged. If the cover has to be kept, then be guided by the description in the Removal of a Support point by means of a gripping stripper.
| PERFORMANCE ORDER |
| 1. Rashplintuyte also release a nut of a finger of a spherical support, a nut not completely not to turn off. |
| 2. Vypressuyte a spherical support from a rotary fist by means of a sliding bifurcate stripper. Grease a cover with jellied lubricant and work carefully not to tear a cover. Turn off a support finger nut. |
|
|
|
| 3. Turn off a bolt and nuts of fastening of a spherical support to the lever of a suspension bracket and separate a support from the lever. |
| 4. At assembly establish a spherical support on a rotary fist and screw a nut, a nut not to tighten. |
| 5. Install a support on the lever, turn and tighten nuts and a bolt with the set moment. |
| 6. Tighten a support finger nut with the set moment and a zashplintuyta (the forelock replace new). If the forelock does not come into nut grooves, then slightly tighten a nut before coincidence of the next groove to the forelock. |
| 7. Establish a wheel and lower the car. |
|
REMOVAL OF THE SUPPORT BY MEANS OF THE GRIPPING BIFURCATE STRIPPER
| PERFORMANCE ORDER |
| 1. Separate a spherical support from the suspension bracket lever (see subsection 9.1.6.). |
| 2. Get a half shaft from a rotary fist (see subsection 9.3.2.) also suspend, having fixed by a wire. |
| 3. Rashplintuyte also release a nut of a finger of a spherical support, a nut not completely not to turn off. |
|
|
4. Dress a gripping part of a stripper and a vypressuyta a spherical support from a rotary fist. |
| 5. Turn off a nut of a finger of a spherical support and remove a support. |
| 6. At assembly establish a new spherical support on a rotary fist and tighten a nut with the set moment. |
| 7. Insert a half shaft into a rotary fist and wrap a nut. Tighten a nut, but not to the full. |
| 8. Install a support on the lever and tighten nuts and a bolt with the set moment. |
| 9. Establish a wheel and lower the car. Tighten nuts of a wheel with the set moment. |
| 10. Tighten a nave nut with the set moment (see subsection 8.3.1.), establish a lock washer and the forelock. |
|
|
|
