Toyota Camry

1996-2001 of release

Repair and operation of the car

Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
- 10. Brake system
   10.2. Technical characteristics
   10.3. ABS system
   10.4. Blocks of disk brakes
   10.5. Brake support
   10.6. Brake disk
   10.7. Blocks of drum brakes
   10.8. Wheel cylinder of brakes
   10.9. Main cylinder of brakes
   10:10. Hoses and tubes of a hydraulic actuator
   10:11. Removal of air from a hydraulic actuator of brakes
   10:12. Vacuum amplifier of brakes
   10:13. Blocks of the parking brake of back disk brakes
   10:14. Parking brake
   10:15. Cables of the parking brake
   10:16. Braking signal switch
   10:17. ABS: natural choice
   10:18. Malfunctions of the brake system
+ 11. Body
+ 12. Electric equipment

Welx websitehttps://welx.net

10.5. Brake support

GENERAL INFORMATION

Details of a forward brake (for models with the 4-cylinder engine)

1. Support
2. Support arm
3. Sealant
4. Finger
5. Rubber cover
6. Clamps of blocks (for cars with the engine 5S-FE)
7. Clamps of blocks (for cars with the engine 1MZ-FE)
8. Antinoise plates
9. Internal antinoise plate
10, 13. Spring of an antinoise plate

11. Internal block
12. External block
14. The index of wear of a block (for cars with the engine 1MZ-FE)
15. Cover
16. Epiploon
17. Finger
18. Sealing ring of the piston
19. Restrictive ring of the piston
20. Piston
21. The union for pumping of a brake

Details of a forward brake (for models with the 6-cylinder engine)

1. Support
2. Support arm
3. Disk
4. Sealant
5. Finger
6. Epiploon
7. Rubber cover
8. Clamps of blocks
9. Antinoise plates
10. Spring of an antinoise plate

11. External block
12. Internal block
13. Index of wear of a block
14. Cover
15. Finger
16. External sealant
17. Restrictive ring of the piston
18. Piston
19. Sealing ring of the piston
20. The union for pumping of brakes

Details of a back brake

1. Sealant
2. Support
3. The union for pumping of brakes
4. Support axis cover
5. External sealant of the piston
6. Piston
7. Sealing ring of the piston
8. Restrictive ring of the piston
9. Epiploon

10. Block clamp
11. Block
12. Internal antinoise plate
13. Antinoise plate
14. Rubber cover
15. Support assembled
16. Support arm
17. Cap
18. Disk

Removal

Prevention

Supports change in couple on one axis.

PERFORMANCE ORDER

1. Lift the car and remove wheels.
	2. Close a brake hose union opening a piece of a rubber hose of suitable diameter. Turn off a bolt of the union and disconnect a brake hose.
3. Turn off bolts of fastening and remove a support.

4. If necessary remove an arm from a rotary fist or an arm of a back axis, having turned off the bolts specified by shooters. In the drawing at the left – an arm of a forward support, on the right – back.

Installation

Installation is carried out upside-down. Tighten all bolts with the set moment. Remove air from a hydraulic actuator of brakes.