Toyota Camry

1996-2001 of release

Repair and operation of the car

Toyota Camry
+ 1. Maintenance instruction
+ 1.2. Information before driving of the car
+ 1.3. Independent maintenance
+ 1.4. Technical characteristics
+ 1.5. Several councils upon purchase of the car
+ 2. Maintenance
- 3. Engines
   - 3.1.2. Check of a compression
      3.1.3. Top Dead Point (TDP) of the N1 piston
      3.1.4. Cover of a head of cylinders
      3.1.5. Inlet collector
      3.1.6. Final collector
      3.1.7. Gas-distributing belt and asterisks
      3.1.8. Forward epiploon of a bent shaft
      3.1.9. Camshaft epiploon
      3.1.10. Camshafts and elevators of valves
      3.1.11. Head of cylinders
      3.1.12. Oil pallet
      3.1.13. Oil pump
      3.1.14. Flywheel / drive plate
      3.1.15. Back epiploon of a bent shaft
      3.1.16. Fastenings of the engine
   + 3.2. 6-cylinder two-row V6 3,0 engines of l
   + 3.3. Partition of engines
   + 3.4. Engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Transmission
+ 9. Running gear
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

3.1.11. Head of cylinders

GENERAL INFORMATION

Head of cylinders of the engine 5S-FE

1. Valve of system of recirculation
exhaust gases and vacuum converter
2. Laying
3. Laying
4. Throttle
5. A damper of pulsations in fuel system
6. Fuel hose
7. Laying
8. Inlet collector
9. Fuel return hose
10. Fuel supply tube
11. Sealing ring
11a Insulating plug
12. Injector
13. Insulator
14. Plug
15. Valve
16. Cover of a head of cylinders
17. Clamp
18. Adjusting laying
19. The isolating plug
20. Epiploon
21. Valve
22. Spark plug
23. Valve elevator
24. Clamps
25. Plate of a spring
26. Valve spring
27. Spring saddle
28. Lock ring
29. The directing valve plug
30. Camshaft of final valves
31. A hook for an engine raising
32. Cooling system branch pipe

33. Pumping
34. Oil pressure sensor
35. Perepuskny tube of the cooling system
36. The heat-insulating guard of the oil heater
37. The heat-insulating guard of a final collector
38. Kronshtya of a final collector
39. Kronshtya of a final collector
40. Final collector
41. Laying
42. Sealing ring
43. Laying
44. Head of cylinders
45. A hook for an engine raising
46. Ground contact
47. Generator arm
48. Laying of a head of cylinders
49. Cover of a gas-distributing belt
50. Camshaft gear wheel spring
51. Lock ring
52. Washer
53. Epiploon
54. Additional gear wheel of the camshaft
55. Camshaft of inlet valves
56. Cover of the first bearing of a shaft
57. Laying
58. Fastenings of an inlet collector
59. Air tube
60. Laying
61. Vacuum tube
62. Vacuum valve of system of recirculation

Removal

Sequence of tightening of bolts of a head of cylinders

PERFORMANCE ORDER

1. Disconnect a wire of the minus plug of the accumulator.
2. Merge cooling liquid from a case of the engine and from a radiator.
3. Merge engine oil and remove an oil filter.
4. Remove a throttle, fuel injectors and the fuel highway.
5. Remove an inlet collector.
6. Remove a final collector.
7. Take off a gas-distributing belt, an asterisk of the camshaft and the top intermediate pulley.
8. Remove the top section of a back cover of a gas-distributing belt.
9. Remove camshafts and elevators of valves.
10. Remove the generator and the distributor of ignition.
11. Unscrew bolts of the pump of the amplifier of steering. Shift the pump aside, without disconnecting from it hoses.
12. Disconnect all wires, tubes, hoses and ropes fixed on a head of cylinders.
13. Weaken and unscrew head bolts in the sequence of return that which is specified in the drawing Sequence of Tightening of Bolts of a Head of Cylinders. Weaken bolts on a quarter of a turn at one time.
	14. Remove a head of cylinders.

Installation

PERFORMANCE ORDER

	1. Carefully clean and wipe with acetone the joined surfaces of a head and the block of cylinders. If surfaces are scratched or damaged otherwise, then they need to be processed in a specialized workshop.
2. By means of a suitable tap clean carvings in the block of cylinders. By means of a suitable die clean bolts of a head of cylinders.
3. Establish new laying of a head and establish a head.
4. Oil bolts pure engine.
5. Insert bolts and tighten them till the required inhaling moment in the sequence specified in the drawing Sequence of Tightening of Bolts of a Head of Cylinders.
6. Establish the remained details.